Gotta Learn Why?

Here is the video I have on youtube

https://www.facebook.com/reel/1952248175341488 Dual 7-100 Linked back to my Facebook so you can watch it

Another 1 fixed and tuned to the correct psi! Rewired the soft wash system from a 12 gauge on a 7 ft system total of 14 feet total! 5.3 remco 100 psi 19 amps Rewired to 6 gauge wire Changed out the Switch to a new one that can handle 275 amps on the normal.… Read more: Had another local guy over today. Update on what we did to get him right.

Thanks again for all the Gifts & Tips on the site to keep it running.

Here is a video I did for you to understand so many people underestimate

SOME of my locals, Now My FAM!!! Let’s GOOOOO I am trying to upload everything now and tie back to the site.

I need you to learn WHY. A lot of people don’t know Low Voltage

You will always hear me say this over and over The WHY? Do you see how wrong 90% of these builds are? You have to understand, what you are doing. So you can do the job correctly, right? who wants or needs stress & down time.

It heavy so it sinks to the bottom right? So, now you suck all that soap and you run out. You just wasting your money.

I made this so easy for you. Just 2 clicks and it will add to your cart on amazon. If your running a 12v, 24v & Gas Softwash YOU NEED THIS. All Builders should have this on hand. How do you not check the builds with no PSI checks. That’s just as bad as not… Read more: Soft Wash PSI Gauge Build

You have to understand, what you are building. Please ask questions before spending money and build them incorrectly.

1 AGM Battery holding this much power still after a day of work. I have him do his new setup test with 2 batteies.

When you give these pumps what they need they will make you amazed. All Equiment has a place on a job. Is 12 volt the best? All depends on your work load. Gotta build it right before you can bad mouth a system.

This is when people really talk shit about a pump. Why? because they didn’t install it right. can’t be using 10, 8 you should be on 6 gauge wire to a bus bar. Then pump off the bar. This pump is surging at 35 plus amps. This is where OHM’S LAW comes into play. Now… Read more: If you run a Delavan pump, thing’s you must know

For a 5-7 Gpm Soft wash System will shoot better with a Jrod. Here is a link to get it ordered. I’m a Jrod guy for sure!

⚡ Relay (Electromagnetic Switch) A relay is an electrically controlled switch designed mainly to control low-current or medium-current circuits. 🔹 How it works 🔹 Typical specs 🔹 Pros 🔹 Cons 🔩 Solenoid (Heavy-Duty Electromagnetic Switch) A solenoid is basically a heavy-duty relay built for high current and mechanical reliability — like a starter solenoid on… Read more: Relay vs a Solenoid

I always show the proof. So here are a few bulkheads that will cause you a major headace. when you can’t find the leaks. This is 99% the time cracked. Uniseal 0 connections to the barb. Only 1 leak point right? Feature / Factor Uniseal 🟢 Bulkhead 🔴 Leak Points 1 (pipe + seal) 3+… Read more: UNISEAL over BulkHeads here is the WHY

Please don’t just DROP the SOAP in. What a waste of money and uneven soap. Use a paint paddle mixer. Mix it for awhile. Most soaps are heavy and will sink to the bottom. So you will draw all that soap up fast and be out.

This is another thing I started seeing down the road. All you see is fiters right before the pump. What happen to filtering before the pump so aren’t sucking dirty water into your soft wash system.

I have mine here! Here are some extra stuff that might help you install.

$108.00 – One and Done.Invest once, wire it right, and never stress again. (As long as you take care of it, that wire’s built to outlast your pump!)

you are all underwired, underrated switch & not enought storage

Proper Install Checklist – 12V / 24V Soft-Wash Systems To do a proper install, you must start with the right tools and the right numbers.

You must know the correct fuse for the line you’re running.You can’t put a 30-amp breaker or fuse on 20-amp rated wire — that’s asking for a meltdown, not performance.Always size your protection to the wire rating, not the pump draw.

The only wire I will run on a setup. We are building a salt water boat. So no bare copper should be used. 6 AWG 80 amp wire so we have enought for this setup.