I always show the proof. So here are a few bulkheads that will cause you a major headace. when you can’t find the leaks. This is 99% the time cracked. Uniseal 0 connections to the barb. Only 1 leak point right?
| Feature / Factor | Uniseal 🟢 | Bulkhead 🔴 |
|---|---|---|
| Leak Points | 1 (pipe + seal) | 3+ (threads, gasket, O-rings) |
| Flexibility | Flexible – allows tank wall movement | Rigid – stress cracks more common |
| Ease of Install | Drill hole, push pipe through | Drill hole, align fittings, tighten threads |
| Vibration Resistance | Excellent – absorbs pump vibration | Poor – loosens over time |
| Chemical Resistance (SH) | Strong – less exposed surface area | Weaker – threads & gaskets degrade faster |
| Profile Inside Tank | Low profile | Bulky (threads & nut take space) |
| Maintenance | Easy – pop out & replace | Harder – requires tools, re-tightening |
| Air Leak Risk | Low | High – especially around threads |
| Cost | Lower | Higher (extra fittings) |
| Best Use | Downstream lines, SH, water, soap | Rarely preferred; only if rigid threaded connection is required |
- How to Get Leads all for free. Learn how to use the toolsHere is the video I have on youtube
- You want a 1% Voltage Drop Not 5% YUK
- New Video Over 400k View wowhttps://www.facebook.com/reel/1952248175341488 Dual 7-100 Linked back to my Facebook so you can watch it
- Had another local guy over today. Update on what we did to get him right.Another 1 fixed and tuned to the correct psi! Rewired the soft wash system from a 12 gauge on a 7 ft system total of 14 feet total! 5.3 remco 100 psi 19 amps Rewired to 6 gauge wire Changed out the Switch to a new one that can handle 275 amps on the normal.… Read more: Had another local guy over today. Update on what we did to get him right.
- A must watch on why you must use 1% drop
- The wire on the pump has nothing to do with the install
- WHY you never want a 5% plus voltage drop
- A really good video on wire and buildsThanks again for all the Gifts & Tips on the site to keep it running.
- Another New Video for you. Some random import info.
- Learn about pumps & more
- Please watch you must understand how works
- A MUST Watch!! I teach everything here and Why?
- Tips, Guns & Etc
- Why you must run numbers and here listen to me
- Have to keep and eye on the Temp of the wireHere is a video I did for you to understand so many people underestimate
- So much posted this week!SOME of my locals, Now My FAM!!! Let’s GOOOOO I am trying to upload everything now and tie back to the site.
- If your demand pump breaks. This is how to fix it.
- Let’s look over this systemI need you to learn WHY. A lot of people don’t know Low Voltage
- The wiring is key to a succesful buildYou will always hear me say this over and over The WHY? Do you see how wrong 90% of these builds are? You have to understand, what you are doing. So you can do the job correctly, right? who wants or needs stress & down time.
- You Must mix with a drill. The pour method doesn’t work!It heavy so it sinks to the bottom right? So, now you suck all that soap and you run out. You just wasting your money.
- Soft Wash PSI Gauge BuildI made this so easy for you. Just 2 clicks and it will add to your cart on amazon. If your running a 12v, 24v & Gas Softwash YOU NEED THIS. All Builders should have this on hand. How do you not check the builds with no PSI checks. That’s just as bad as not… Read more: Soft Wash PSI Gauge Build
- Happy Veterans Day!!
- Storage is your RUN-TIMEYou have to understand, what you are building. Please ask questions before spending money and build them incorrectly.
- What a Voltage Drop test looks like, Dan did one for use after his day of work and still holds over 12 volts. This an old video but shows the facts1 AGM Battery holding this much power still after a day of work. I have him do his new setup test with 2 batteies.
- More on the wiring and switch, New Video
- Each system needs a diffrent build. Must learn the right way how to do it. It’s Not the PumpWhen you give these pumps what they need they will make you amazed. All Equiment has a place on a job. Is 12 volt the best? All depends on your work load. Gotta build it right before you can bad mouth a system.
- If you run a Delavan pump, thing’s you must knowThis is when people really talk shit about a pump. Why? because they didn’t install it right. can’t be using 10, 8 you should be on 6 gauge wire to a bus bar. Then pump off the bar. This pump is surging at 35 plus amps. This is where OHM’S LAW comes into play. Now… Read more: If you run a Delavan pump, thing’s you must know
- Eddie, What Jrod do I need?For a 5-7 Gpm Soft wash System will shoot better with a Jrod. Here is a link to get it ordered. I’m a Jrod guy for sure!
- How I test a pump, to find issues
- Relay vs a Solenoid⚡ Relay (Electromagnetic Switch) A relay is an electrically controlled switch designed mainly to control low-current or medium-current circuits. 🔹 How it works 🔹 Typical specs 🔹 Pros 🔹 Cons 🔩 Solenoid (Heavy-Duty Electromagnetic Switch) A solenoid is basically a heavy-duty relay built for high current and mechanical reliability — like a starter solenoid on… Read more: Relay vs a Solenoid
- UNISEAL over BulkHeads here is the WHYI always show the proof. So here are a few bulkheads that will cause you a major headace. when you can’t find the leaks. This is 99% the time cracked. Uniseal 0 connections to the barb. Only 1 leak point right? Feature / Factor Uniseal 🟢 Bulkhead 🔴 Leak Points 1 (pipe + seal) 3+… Read more: UNISEAL over BulkHeads here is the WHY
- You must MIX your SOAPPlease don’t just DROP the SOAP in. What a waste of money and uneven soap. Use a paint paddle mixer. Mix it for awhile. Most soaps are heavy and will sink to the bottom. So you will draw all that soap up fast and be out.
- You have to Filter before the Water TankThis is another thing I started seeing down the road. All you see is fiters right before the pump. What happen to filtering before the pump so aren’t sucking dirty water into your soft wash system.
- These are the tools you need for big wireI have mine here! Here are some extra stuff that might help you install.
- I made you a Starter Kit, Set it and forget it lol$108.00 – One and Done.Invest once, wire it right, and never stress again. (As long as you take care of it, that wire’s built to outlast your pump!)
- Please watch and listen to this pleaseyou are all underwired, underrated switch & not enought storage
- A MUST have, to installProper Install Checklist – 12V / 24V Soft-Wash Systems To do a proper install, you must start with the right tools and the right numbers.
- Not a good idea!You must know the correct fuse for the line you’re running.You can’t put a 30-amp breaker or fuse on 20-amp rated wire — that’s asking for a meltdown, not performance.Always size your protection to the wire rating, not the pump draw.
- My wire I useThe only wire I will run on a setup. We are building a salt water boat. So no bare copper should be used. 6 AWG 80 amp wire so we have enought for this setup.